Payment Method
8102001CA +BOM
CMOS Low-Power Monostable/Astable Multivibrator
14-CDIP(0.300",7.62mm)-
Manufacturer:
Texas Instruments
-
Mfr.Part #:
8102001CA
-
Datasheet:
-
Series:
4000B
-
Logic Type:
Astable, Monostable
-
Independent Circuits:
1
-
Schmitt Trigger Input:
No
-
EDA/CAD Models:
All bill of materials (BOM) can be sent via email to [email protected], or fill below form to Quote for 8102001CA, guaranteed quotes back within 12hr.
Availability: 9176 PCS
Please fill in the short form below and we will provide you the quotation immediately.
8102001CA General Description
CD4047B consists of a gatable astable multivibrator with logic techniques incorporated to permit positive or negative edge-triggered monostable multivibrator action with retriggering and external counting options.
Inputs include +TRIGGER, -TRIGGER, ASTABLE, ASTABLE\, RETRIGGER, and EXTERNAL RESET. Buffered outputs are Q\, Q and OSCILLATOR. In all modes of operation, and external capacitor must be connected between C-Timing and RC-Common terminal, and an external resistor must be connected between the R-Timing and RC-Common terminals.
Astable operation is enabled by a high level on the STABLE input or a low level on the ASTABLE\ input, or both. The period of the square wave at the Q and Q\ Outputs in this mode off operation is a function of the external components employed. "True" input pulses on the ASTABLE input or "Complement" pulses on the ASTABLE\ input allow the circuit to be used as a gatable multivibrator. The OSCILLATOR output period will be half of the Q terminal output in the astable mode. However, a 50% duty cycle is not guaranteed at this output.
The CD4047B triggers in the monostable mode when a positive-going edge occurs on the +TRIGGER-input while the -TRIGGER is held low. INput pulses may be of any duration relative to the output pulse.
If retrigger capability is desired, the RETRIGGER input is pulsed. The retriggerable mode of operation is limited to positive-going edge. The CD4047B will retrigger as long as the RETRIGGER-input is high, with or without transitions (See Fig. 34).
An external countdown option can be implemented by coupling "Q" to an external "N" counter and resetting the counter with the trigger pulse. The counter output pulse is fed back to the ASTABLE\ input and has a duration equal to N times the period of the multivibrator.
A high level on the EXTERNAL RESET input assures no output pulse during an "ON" power condition. This input can also be activated to terminate the output pulse at any tine. For monostable operation, whenever VDD is applied, and internal power-on reset circuit will clock the Q output low within one output period (tM).
The CD4047B-Series types are supplied in 14-lead hermetic dual-in-line ceramic packages (F3A suffix), 14-lead dual-in-line plastic packages (E suffix), 14-lead small outline packages (M, MT, M96, and NSR suffixes), and 14-lead thin shrink small-outline packages (PW and PWR suffixes).
Key Features
- Lower power consumption: special CMOS oscillator configuration
- Monostable (one-shot) or astable (free-running) operation
- True and complemented buffered outputs
- Only one external R anc C required
- Buffered inputs
- 100% tested for quiescent current at 20 V
- Standardized, symmetrical output characteristics
- 5-V, 10-V, and 15-V parametric ratings
- Meets all requirements of JEDEC Tentative Standard No. 13B, "Standard Specifications for Description of 'B' Series CMOS Devices"
- Monostable Multivibrator Features:
- Positive-or negative-edge trigger
- Output pulse width independent of trigger pulse duration
- Retriggerable option for pulse width expansion
- Internal power-on reset circuit
- Long pulse widths possible using small RC components by means of external counter provision
- Fast recovery time essentially independent of pulse width
- Pulse-width accuracy maintained at duty cycles approaching 100%
- Astable Multivibrator Features:
- Free-running or gatable operating modes
- 50% duty cycle
- Oscillator output available
- Good astable frequency stability:
Frequency deviation:
= ±2% + 0.03%/°C @ 100 kHz
= ±0.5% +0.015%/°C @ 10 kHz (circuits "trimmed" to frequency VDD = 10 V ± 10%)
- Applications:
Digital equipment where low-power dissipation and/or high noise immunity are primary design requirements:- Envelope detection
- Frequency multiplication
- Frequency division
- Frequency discriminators
- Timing circuits
- Time-delay applications
Data sheet acquired from Harris Semiconductor
Specifications
Series | 4000B | Logic Type | Astable, Monostable |
Independent Circuits | 1 | Schmitt Trigger Input | No |
Propagation Delay | 150 ns | Current - Output High, Low | 6.8mA, 6.8mA |
Voltage - Supply | 3 V ~ 18 V | Operating Temperature | -55°C ~ 125°C |
Mounting Type | Through Hole |
Service Policies and Others
After-Sales & Settlement Related
For alternative payment channels, please reach out to us at:
[email protected]Shipping Method
AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.
365-Day Product
Quality Guarantee
We promise to provide 365 days quality assurance service for all our products.
In Stock: 9,176
Minimum Order: 1
Qty. | Unit Price | Ext. Price |
---|---|---|
1+ | - | - |
The prices below are for reference only.
Featured Products
Top Sellers
-
C100
Issi
Video ICs 4MP H.265 Video Processor - 64MB DDR2, BGA85, 5mm x 6mm
-
NE555
Texas Instruments
100kHz operation frequency with low power consumption for long-lasting performance
-
CD4017
Onsemi
Compact digital counter for precision measurement application
-
74LS04
Onsemi
High-quality die for professional use only, unsurfaced and untested
-
TDA2050
Stmicroelectronics
Effortlessly drives your speakers with crystal-clear sound and robust power