Payment Method
ATSAMB11-MR210CA +BOM
This module is designed for seamless Bluetooth communication, supporting 802.15.1 standards for reliable wireless connections
Module-
Manufacturer:
Microchip Technology
-
Mfr.Part #:
ATSAMB11-MR210CA
-
Datasheet:
-
Series:
SmartConnect
-
Programmabe:
Not Verified
-
RF Family/Standard:
Bluetooth
-
Protocol:
Bluetooth v4.1
-
EDA/CAD Models:
Send all BOMs to [email protected], or fill out the form below for a quote on ATSAMB11-MR210CA. Guaranteed response within 12hr.
Availability: 8566 PCS
Please fill in the short form below and we will provide you the quotation immediately.
ATSAMB11-MR210CA General Description
Catering to the needs of battery-powered devices, the ATSAMB11-MR210CA boasts impressive energy efficiency, ensuring prolonged operational performance. Thanks to its ARM Cortex-M0 processor, the module delivers robust processing power for seamless application execution and efficient communication handling. Moreover, its support for various Bluetooth profiles and protocols guarantees compatibility with a wide spectrum of devices and systems, further enhancing its versatility. With built-in security measures, this module prioritizes data integrity and secure communications, catering to the stringent security requirements of modern applications
Key Features
- Core
- – ARM® Cortex®-M3 revision 2.0 running at up to 64 MHz
- – Memory Protection Unit (MPU)
- – Thumb®-2 instruction set
- Pin-to-pin compatible with AT91SAM7S series (48- and 64-pin versions)
- Memories
- – From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator, single plane
- – From 16 to 48 Kbytes embedded SRAM
- – 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines
- – 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support
- – Memory Protection Unit (MPU)
- System
- – Embedded voltage regulator for single supply operation
- – Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation
- – Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low power 32.768 kHz for RTC or device clock
- – High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. Inapplication trimming access for frequency adjustment
- – Slow Clock Internal RC oscillator as permanent low-power mode device clock
- – Two PLLs up to 130 MHz for device clock and for USB
- – Temperature Sensor
- – Up to 22 peripheral DMA (PDC) channels
- Low Power Modes
- – Sleep and Backup modes, down to 1.8 µA in Backup mode
- – Ultra low power RTC
- Peripherals
- – USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip Transceiver
- – Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and Modem Mode
- – Two 2-wire UARTs
- – Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller (I2S), 1 High Speed Multimedia Card Interface (SDIO/SD Card/MMC)
- – Up to 6 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM mode. Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper Motor
- – 4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control
- – 32-bit Real-time Timer and RTC with calendar and alarm features
- – Up to 15-channel, 1Msps ADC with differential input mode and programmable gain stage
- – One 2-channel 12-bit 1Msps DAC
- – One Analog Comparator with flexible input selection, Selectable input hysteresis
- – 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)
- – Write Protected Registers
- – Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination
- – Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel Capture Mode
- Packages
- – 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm
- – 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm
- – 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5 mm
Specifications
Series | SmartConnect | Programmabe | Not Verified |
RF Family/Standard | Bluetooth | Protocol | Bluetooth v4.1 |
Frequency | 2.4GHz | Power - Output | 4dBm |
Sensitivity | -96dBm | Serial Interfaces | I2C, SPI, UART |
Antenna Type | Integrated, Chip | Memory Size | 256kB Flash, 128kB ROM, 128kB RAM |
Voltage - Supply | 2.3V ~ 3.6V | Current - Receiving | 4mA |
Current - Transmitting | 3mA | Mounting Type | Surface Mount |
Base Product Number | ATSAMB11 |
Service Policies and Others
After-Sales & Settlement Related
For alternative payment channels, please reach out to us at:
[email protected]Shipping Method
AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.
365-Day Product
Quality Guarantee
We promise to provide 365 days quality assurance service for all our products.
In Stock: 8,566
Minimum Order: 1
Qty. | Unit Price | Ext. Price |
---|---|---|
1+ | - | - |
The prices below are for reference only.
Featured Products
Top Sellers
-
ESP8266
1-Avel
Access your WiFi network with the ESP8266 WiFi Module, a self-contained SOC with TCP/IP protocol stack integration
-
ESP-WROOM-32
ESPRESSIF
Compact ESP-WROOM- module for IoT project
-
SIM800L
* Other *
High-Speed GPRS Capabilities and Reliable GSM Communication in One Small Packag
-
ESP-12E
Ai-Thinker
Perfect solution for smart home, industrial, or wearables projects: compact, high-speed Wi-Fi connectivity at an affordable pric
-
SIM900
Simcom
Streamline your device connectivity worldwide using SIMs advanced quad-band GSM/GPRS module, designed for mission-critical applications